12T capacity 1300 model swing shear cut to length line
It equips with swing shear so it can cut strips into trapezoidal blanks which are widely used in stamping auto parts area, metal electrical appliances parts etc.
It has advantages of cost saving, space saving, high efficiency etc. if just cut into trapezoidal shape blanks than blanking by punching machine blanking line, as it cost much higher of punching machine than swing shear machine.
Main components of the cut to length line
1. One set of NCHW2-1300A model 3 in 1 uncoiler straightener feeder.
2. One set of swing shear.
3. One set of conveyor belt.
4. One set of auto stacking system.
Coil was loaded, lifted and installed on decoiler’s mandrel by the auto loading car, then decoiler payoff strips and insert strip head into straightener feeder part, electric adjust straightener gap device to adjust straightening performance automatically then feed strips to swing shear after processed by straightener feeder part. Next, swing shear cut strips to required trapezoidal shape, next, the blank were carried out by the conveyor belt and come to auto stacking system.
1 For NCHW2-1300A model 3 in 1 uncoiler straightener feeder
1.1 12T Uncoiler
- Function instruction: uncoiling is to fix coil on the spindle of uncoiler, a supporting table to support coil Inner diameter, while working automatically, through material loop controlling instruction to make spindle uncoiling and loosing coil intermittently, equipped with coil diameter detection, to control uncoiling speed, ensure uncoiling line speed is uniform velocity, improved material loose problem.
- Components included: expansion and contraction part, press arm part, limit wheel part, material loop controlling part.
- Material width: 70-1300mm;
- Loading capacity:12T
- Coil OD: Φ1000mm~Φ1600mm
- Hydraulic slide block expansion mandrel, spindle expansion range: Φ470-Φ530mm. It can support and expansion heavy coils over 12Tons.
- Hydraulic tailstock arm device. It was used to hold one end of mandrel’s main shaft, so as to it has enough loading capacity of the decoiler.
- Spindle driven motor: AC motor, with frequency converter. Spindle driven method: variable frequency gear motor.
- Spindle brake: disc brake. Spindle uncoiling direction: down uncoiling.
- Press material wheel specification: PU rubber tires Press material wheel driven method: AC motor, with frequency converter.
- Function of press arm: from cut off bundling belt which is used for fixing coil until the coil head is pressed tightly by straightener roller, to prevent coil rebounding; while whole feeding line working, let the coil uncoiling smoothly, to prevent coil dispersing. and the press arm is motorized, with tracking and follow up function, ie. Rotating speed of press arm roller is absolutely the same with uncoiling line speed, then tightening metal strip, to prevent coil loosing.
- Press material wheel adjusting method: through change angle of press arm to change encoder feedback single to adjust speed.
- Press arm moving method: driven by hydraulic cylinder, can be opened or closed manually.
- Limit arm device: located on decoiler’s right part, can be rotated along with any external force, for preventing coil of side slip while payoff.
- Limit wheel motion: outer limit wheel is doing open/close motion driven by air cylinder, internal limit wheel without open/close motion, just move along direction of coil width, outer limit wheel just can be operated by touch screen in manual version, while automatically working, it need to be closed, then can meet safety requirement of before working.
- Surface process of limit wheel: high frequency with parkerising for rust protection.
- Material loop control: through induct material loop to feedback signal by the infrared photoelectricity induction switch under press arm, to control uncoiler spindle of start/stop, to ensure enough buffer material loop between uncoiler and straightener.
1.2 Loading car:
- Function instruction: be used for moving coil to spindle of uncoiler smoothly, while uncoiling and entry the material head into straightener, it is used for supporting material head to let it entry into straightening roller smoothly, loading car is equipped with backup plate to prevent coil slipping off from loading car while moving little big distance, while hanging coil.
- Loading capacity: 12T
- Loading car moving method: hydraulic motor.
- Loading car lifting method: hydraulic method (controlled by pressure retaining valve, stable and reliable).
- Moving method of backup plate for preventing slipping down: by manual.
1.3 Straightener-Feeder part
- Function instruction: use unbending principle to release material bending stress to straighten plate, then feed into press equipment according to set length and speed.
- Bend arm device. Strip head was assisted by support arm and then press down by press arm device, then motorized rollers feed strip forwards to go through straightener feeder part.
- Driven method: AC servo motor+ speed reducer: 11.0KW PHASE, ITALY
Electric adjust straightening roller gap. Driven by 2set of servo motor/hydraulic motor to adjust straightener roller gap (refer to above image), just need to set data in HMI’s touch screen(refer to the following image). Moreover, it has the function of memory and call it back of the producing data: such as different products different part code, straightener gap set data.(Refer to following image)
It also can memory and call it back of data such as feeding length, feed speed, part code etc.
- Straightening-feeding roller combination: straightening roller; assistant roller; feeding roller. Straightening roller: 9pcs (upper5pcs/down4pcs), Φ68mm.
- Backup roller device (Assistant roller): 3 columns at upper and down, making the straightening rollers have enough intensity to flat thickness and high tensile material and ensure straightening accuracy (refer to the following image).
- Feeding roller: 2pcs Φ84mm.
- Straightening measure display method: dial display.
- Coil end detect device. It equips with sensor device, when it detects there is no strip when strip used up, power press can stop and feed also stop, then operator can operate the feeder in manual model to finish the rest stamping work.
- Roller material: GCr15. All straightening rollers, feeding rollers adopt high quality of GCr15 and finished tempering & quenching
- Roller driven method: gear driving, all gears adopt tempering, carburization, high frequency quenching, precise grinding gear IT6 level precise standard.
- Feeding precise: 0-1000mm, ±0.15mm/m(mould with pin can reach 0.05mm); above 1000mm, ±0.20mm/m.
- Material exit support plate length: 400-1000mm (can be customized), the length usually was customized according to the buyer’s requirement.
2. Swing shear
Cutting capacity: 70-1300mm width, 0.5-4.5mm thickness
Swing angle: ±45°
Cutting accuracy: ±0.5mm
3. Conveyor belt and auto stacking system
- It’s PVC belt type conveyor belt, it was used to carry blanks from swing shear’s exit to auto stacking system. Running speed is adjustable as it equips with inverter.
- For the auto stacking system, It’s designed to laminate and stacking blanks automatically.
- It can be customized based on blanks shape, laminating height, stacking station quantity etc. or the customer’s requirements.
- Lamination height can be 500-1000mm or as requirements.